- Get product recommendations
- Easily find parts & accessories
- Lug Nuts & Locks
- Wheel Spacers
- Mud Flaps
- Bull Bar
- Tonneau Covers
- Body Kits
- Side Window Deflectors
- Fender Flares & Trim
- Step Bars
- Off-Road Bumpers
- Wheel Well Guard
- Electric Winch
- Hood Deflectors
- Roof Deflectors
- Bumper Protectors
- Light Covers & Lamp Guards
- Auto Detailing
- Exterior Trim
- Grille Guards
- Roof Racks & Storage
- Armor & Protection
- Soft Tops & Hard Tops
- License Plate Frame & Bracket
- Emblems & Logos
- Spare Carrier
- Tow Hook
- Clutch Kits
- Clutch Discs
- Pressure Plates
- Transmission Cooling
- Shifter & Levers
- Transmission Fluids
- Electronics Components
- Clutch Linkages
- Drive Shaft
- Driveshaft Yokes
- Oil Pan
- Torque Converters
- Wheel Bearings & Hubs
- Transmission Shafts & Gears
AEM | WATER / METHANOL INJECTION KIT V3 - 1.15 GALLON
The AEM Water Injection Kit reduce air inlet temperatures to increase boost pressure for more power. Lower air inlet temperatures allow users to advance timing without having to run higher-octane fuel.
- PROUDLY CANADIAN
- BEST PRICE GUARANTEE
- GUARANTEED FITMENT
AEM WATER / METHANOL INJECTION KIT V3
(w/1.15 Gallon Tank)
30-3300 (Boost 0-35PSI)Â orÂ 30-3350 (MAP Voltage 0-5V)
THE AEM WATER/METHANOL INJECTION SYSTEM ADVANTAGE
Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timingâ€”without using high-octane racing fuelâ€”for power gains of up to 20%. AEMâ€™s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.
Water/Methanol for All Boost Levels of Forced Induction Gas Race Engines
AEM offers two different water/methanol controller designs for gas vehicles:
One is boost dependent for forced induction vehicles up to 35 PSI of boost (kit PN 30-3300). The Boost Dependent controller has an on-board manifold absolute pressure (MAP) sensor with a molded-in nipple for a boost hose pickup.
The second controller (Kit PN 30-3350) features a multiple input design that enables users to install AEMâ€™s Water/Methanol Injection Kit on ultra-high boost vehicles (above 35 PSI) using a 0-5v voltage-based external MAP sensor.
Note: FOR OPTIMUM RESULTS, ALL WATER/METHANOL INJECTION SYSTEMS AND GAUGES SHOULD BE RUN WITH AN AEM INLINE FILTER (AEM PART #30-3003)
Important Safety Notice Regarding Methanol
AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.
All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.
Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you.
Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol.
- Livraison GRATUITE / FREE Delivery
Customers who bought this product also bought:
AEM Electronics | Water / Meth Injection
People who viewed this item also viewed