-
Shop by Category
-
- Floor Mats
- Shift Knobs
-
- Gauge Kits
- Speedometer Gauges
- Tachometers & Shift Lights
- Temperature Gauges
- Voltmeter Gauges
- Fuel Level Gauges
- Pressure Gauges
- Air Fuel Ratio Gauges (AFR)
- Boost & Vacuum Pressure Gauges
- Pyrometer Gauges
- Race Dashes
- Custom Gauge Mounts & Trim
- Gauge Sensors & Adapters
- Gauge Wiring & Lights
- Driving Monitors & Data Loggers
- Timers, Hourmeters & Clocks
- Interior Trim
- Pedals
- Car Organizers
- Accessories
- Car Seats
- Steering Wheels
- Auto Detailing
- Cargo Liners
- Seat Covers
- Sun Shades
- Anti-Theft
-
- Wheel Spacers
- Mud Flaps
- Bull Bar
- Side Window Deflectors
- Hood Deflectors
- Roof Deflectors
- Fender Flares & Trim
- Grilles
- Horns
- Mirror
- Wheel Well Guard
- Door Sill & Bumper Protectors
- Light Covers & Lamp Guards
- Auto Detailing
- Exterior Trim
- Grille Guards
- Armor & Protection
- Soft Tops & Hard Tops
- License Plate Frame & Bracket
- Emblems & Logos
- Antenna
- Spare Carrier
- Tow Hook
-
- Housses
- Off-Road accessories
-
-
-
- Clutch Kits
- Clutch Discs
- Pressure Plates
- Flywheels
- Transmission Cooling
- Mount
- Shifter & Levers
- Transmission Fluids
- Axle
- Electronics Components
- Clutch Linkages
- Differentials
- Drive Shaft
- Driveshaft Yokes
- Flexplates
- Oil Pan
- Torque Converters
- Wheel Bearings & Hubs
- Transmission
- Transmission Shafts & Gears
-
-
-
- Shop by product
- Shop by brand
- WHEELS & TIRES
- Contact us
-
My garageAdd vehicle
My garage
- Get product recommendations
- Easily find parts & accessories
- -10%
- FREE SHIPPING
JLT Performance | Cold Air Intake - Mustang SVT Cobra 2003-2004
JLT Cold Air Intake Kit (2003-04 SVT COBRA) *No Tuning Required
- PROUDLY CANADIAN
- BEST PRICE GUARANTEE
- GUARANTEED FITMENT
INTAKE TUBE
Using the original JLT CAI as a guide, we molded, sculpted and perfected everything until we had the best looking, fitting and performing system you can buy.
The JLT tube is 4 1/4" ID, roto molded plastic to resist engine heat and keep the intake air charge nice and cool. NO METAL TUBING HERE!!
MAF and filter relocated into fender well for a cooler intake charge and can support up to 550 RWHP.
MOLDED IN MAF
The best part of this new JLT Cold Air is we kicked the cool factor up a notch and molded a 105mm MAF housing right in the tube. Now you have a kit you can grow into and not have to buy a complete new kit when you reach over 550 RWHP. Putting a Whipple or Kenne Bell blower on your 03, 04 Cobra? Simply drill out the pre molded plug on the MAF block located on the bottom of the tube, discreetly out of sight. Install your SCT MAF 2600 or 3000 sensor electronics, add our huge 4.5 X 12” S&B Powerstack filter and you’ve now changed your JLT Cold Air Intake into a JLT High Boost 12” Intake. Molding the MAF into the tube makes for a much smoother air flow with no couplers, reducers or separate MAF housing and can support 800+RWHP for only the cost of the 12” upgrade kit, $60.00.
Will not work with stock MAF, SCT 2400 or 2800 MAF
GAINS
26-30 RWHP are typical with this kit.
EASY INSTALL
The new design, detailed instructions and online video instructions helps make this an easy install (see Instruction & Video tabs to view)
KIT INCLUDES:
- JLT Plastic Intake Tube
- Silicone Coupler
- Silicone Reducer
- Apron Plate
- 4x6 S&B Powerstack Air Filter
- MAF Adapter
- MAF Adapter Gasket
- HD Clamps & all needed hardware
Uses stock Mass Air Meter
Will not fit with most strut tower braces or aftermarket K-Members.
MAINTENANCE
To properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.
*The air filter is low in the bumper to get the coolest air possible. While driving in the rain is not an issue, you MUST be aware of flooded streets and deep puddles. *
Note:
- Livraison GRATUITE / FREE Delivery