-
Shop by Category
-
- Tapis Protecteur
- Pommeau de levier de vitesse
-
- Ensembles
- Indicateurs de vitesse
- Tachometers & Shift Lights
- Température
- Voltmètre
- Niveau de carburant
- Manomètres - Pressure Gauges
- Air Fuel Ratio (AFR)
- Boost & Vacuum Pressure
- Pyrometer
- Tableau de bord de course
- Gauge Mounts & Trim sur mesure
- Capteurs et adaptateurs
- Câblage et éclairage
- Moniteurs et enregistreurs de données
- Minuteurs, horodateurs et horloges
- Garniture intérieur
- Pédales
- Rangement intérieur
- Accessoires
- Sièges auto
- Volants
- Entretien Automobile
- Tapis de coffre
- Couvre-siège
- Pare-soleil
- Antivol
-
- Spacer de roues
- Garde-boue
- Bull Bar
- Déflecteurs de vitre
- Déflecteurs de capot
- Déflecteurs de toit
- Fender Flares & Trim
- Grilles
- Klaxon
- Miroir
- Protège aile
- Protecteurs de pare-choc & seuils
- Light Covers & Lamp Guards
- Entretien Automobile
- Garniture extérieur
- Grille Guards
- Renforts et protection
- Toits souples et rigides
- Support & contour de plaque
- Emblèmes et logos
- Antenne
- Support de roue de secours
- Tow Hook
-
- Housses
- Accessoires Off-Road
-
- Engine DressUp
- Refroidisseurs huile
-
- Filtres à huile
- Oil Catch Can
-
- Huiles Moteur
- Fluides de Transmission, Huiles, Additifs
- Additifs pour Huile Moteur
- Liquides de Frein
- Liquides de Direction Assistée
- Antigel & Additifs
- Additifs pour Système de Carburant
- Lubrifiants Différentiels
- Lubrifiants pour Transfer Case
- Lubrifiants pour Suspensions
- Lubrifiants pour Roulements
- Autres
- Support
- Throttle Bodies
- Stage de Performance
- Poulies & Courroies
- Collets de serrage
- Pan à huile
- Gaskets
- Bloc Moteur
- Engine Dress Up
-
-
- Coil Springs
- Coilovers
- Amortisseurs
- Amortisseurs & Ressorts Kits
- Handling Kits
- Lift Kits
- Leveling Kits
- Sway bars & Link kit
- Steering Arms, Rods & Links
- Strut Bars
- Bushing & Support
- Ball Joints
- Composantes alignement
- Control Arm
- Contrôleur
- Steering Dampers
- Suspension à air
- Suspension à lames
- Accessoires
-
- Ensemble embrayage
- Disques de Clutch
- Pressure Plates
- Flywheels
- Transmission Refroidissement
- Supports
- Pommeau & Levier de Vitesse
- Liquide a transmission
- Cardan
- Composantes Électroniques
- Composantes Embrayage
- Différentiels
- Drive Shaft
- Driveshaft Yokes
- Flexplates
- Pan à huile
- Torque Converters
- Bearings & Moyeu de roue
- Transmission
- Transmission Shafts & Gears
-
-
- Extérieur
-
- Ensembles de démarrage et accessoires
- Éviers et drains
- Filtres à eau et cartouches
- Hivernisation
- Pompes
- Raccords de plomberie
- Rafraîchisseurs et adoucisseurs d'eau
- Régulateurs de pression d'eau
- Réservoirs de rétention
- Robinets et accessoires de douche
- Toilettes et accessoires
- Trappes et remplissages d'eau
- Tuyaux de plomberie
- Douches et baignoires
- Chauffe-eau
- Génératrice
-
- MAGASINER PAR PRODUIT
- ACHETER PAR MARQUE
- ROUES & PNEUS
- Contactez-nous
-
Mon garageAjouter un véhicule
Mon garage
- Recevez des recommandations
- Trouvez facilement vos pièces
- -10%
- LIVRAISON GRATUITE
Précédent
keyboard_arrow_left
Suivant
keyboard_arrow_right
ICON Alloys | 2017-20 Ford Raptor Rear Air Bump Kit
95121
2017-2020 FORD RAPTOR REAR AIR BUMP KIT
- Bolt-on installation does not require any fabrication or removal of the bed
- Replaceable noise-reducing striker pad
- Fully serviceable
- ICON 1K tested under rigorous off-road conditions to validate tune, performance, strength, and durability
- 2.5 travel hydraulic bump stop reduces rear end ‘kick and improves overall vehicle performance
- Velocity sensitive technology exponentially increases bottom-out resistance
- Vehicle specific bump stop tune provides smooth engagement and excellent ride quality
- 6061 billet aluminum crossmember increases chassis rigidity to improve overall vehicle dynamics
- Steel clamshell brackets strengthen the frame in critical areas to prevent damage from extreme off-road use
- Adjustable tension rods allow the frame to be preloaded to withstand torsional force during hard impacts
- Heavy duty 1.25 CNC machined nitro steel shafts
- Multi-stage CAD plated body for maximum corrosion resistance
LIVRAISON GRATUITE
CAD $3 839,92
CAD $4 266,58
Économisez 10%
- FIÈREMENT CANADIEN
- GARANTIE DU MEILLEUR PRIX
- COMPATIBILITÉ GARANTI
The ICON Raptor Bump Stop System includes heavy duty steel clamshell brackets, a billet aluminum frame crossmember, adjustable tension rods, hydraulic bump stops, and all of the necessary hardware required to complete the installation. The clamshell brackets, crossmember, and tension rods add strength to the frame to prevent damage during extreme off-road use while increasing chassis rigidity for predictable handling and improved vehicle dynamics. The 2.5 travel hydraulic bump stops feature velocity sensitive technology which means that as the shaft speed increases the damping ability ramps up, resulting in exponential bottoming resistance that wont negatively affect articulation. Combining all of these components into an easy to install, bolt-on package, ICON has developed the most comprehensive rear bump stop solution on the market for Raptor owners seeking the next level of strength and performance.
Noter:
- Livraison GRATUITE / FREE Delivery
Not Application Specific
Précédent
keyboard_arrow_left
Suivant
keyboard_arrow_right