-
MAGASINER PAR CATÉGORIE
-
- Tapis Protecteur
- Pommeau de levier de vitesse
-
- Ensembles
- Indicateurs de vitesse
- Tachometers & Shift Lights
- Température
- Voltmètre
- Niveau de carburant
- Manomètres - Pressure Gauges
- Air Fuel Ratio (AFR)
- Boost & Vacuum Pressure
- Pyrometer
- Tableau de bord de course
- Gauge Mounts & Trim sur mesure
- Capteurs et adaptateurs
- Câblage et éclairage
- Moniteurs et enregistreurs de données
- Minuteurs, horodateurs et horloges
- Garniture intérieur
- Pédales
- Rangement intérieur
- Accessoires
- Sièges auto
- Volants
- Entretien Automobile
- Tapis de coffre
- Couvre-siège
- Pare-soleil
- Antivol
-
- Spacer de roues
- Garde-boue
- Bull Bar
- Déflecteurs de vitre
- Déflecteurs de capot
- Déflecteurs de toit
- Fender Flares & Trim
- Grilles
- Klaxon
- Miroir
- Protège aile
- Protecteurs de pare-choc & seuils
- Light Covers & Lamp Guards
- Entretien Automobile
- Garniture extérieur
- Grille Guards
- Renforts et protection
- Toits souples et rigides
- Support & contour de plaque
- Emblèmes et logos
- Antenne
- Support de roue de secours
- Tow Hook
-
- Housses
- Accessoires Off-Road
-
-
- Filtres à huile
- Oil Catch Can
-
- Huiles Moteur
- Fluides de Transmission, Huiles, Additifs
- Additifs pour Huile Moteur
- Liquides de Frein
- Liquides de Direction Assistée
- Antigel & Additifs
- Additifs pour Système de Carburant
- Lubrifiants Différentiels
- Lubrifiants pour Transfer Case
- Lubrifiants pour Suspensions
- Lubrifiants pour Roulements
- Autres
- Support
- Throttle Bodies
- Stage de Performance
- Poulies & Courroies
- Collets de serrage
- Pan à huile
- Gaskets
- Bloc Moteur
- Engine Dress Up
-
-
- Coil Springs
- Coilovers
- Amortisseurs
- Amortisseurs & Ressorts Kits
- Handling Kits
- Lift Kits
- Leveling Kits
- Sway bars & Link kit
- Steering Arms, Rods & Links
- Strut Bars
- Bushing & Support
- Ball Joints
- Composantes alignement
- Control Arm
- Contrôleur
- Steering Dampers
- Suspension à air
- Suspension à lames
- Accessoires
-
- Ensemble embrayage
- Disques de Clutch
- Pressure Plates
- Flywheels
- Transmission Refroidissement
- Supports
- Pommeau & Levier de Vitesse
- Liquide a transmission
- Cardan
- Composantes Électroniques
- Composantes Embrayage
- Différentiels
- Drive Shaft
- Driveshaft Yokes
- Flexplates
- Pan à huile
- Torque Converters
- Bearings & Moyeu de roue
- Transmission
- Transmission Shafts & Gears
-
-
- Extérieur
-
- Ensembles de démarrage et accessoires
- Éviers et drains
- Filtres à eau et cartouches
- Hivernisation
- Pompes
- Raccords de plomberie
- Rafraîchisseurs et adoucisseurs d'eau
- Régulateurs de pression d'eau
- Réservoirs de rétention
- Robinets et accessoires de douche
- Toilettes et accessoires
- Trappes et remplissages d'eau
- Tuyaux de plomberie
- Douches et baignoires
- Chauffe-eau
- Génératrice
-
- MAGASINER PAR PRODUIT
- ACHETER PAR MARQUE
- ROUES & PNEUS
- Contactez-nous
-
Mon garageAjouter un véhicule
Mon garage
- Recevez des recommandations
- Trouvez facilement vos pièces
- -5%
- LIVRAISON GRATUITE
CorkSport | Non-Resonated Cat-Back Exhaust 80mm - Mazda 3 Hatchback 2014-2018
CorkSport; Have you just picked up a Turbo Kit for your 2014-2018 Mazda 3 and want to ensure you get the most power out of your setup without sacrificing additional drone?
- FIÈREMENT CANADIEN
- GARANTIE DU MEILLEUR PRIX
- COMPATIBILITÉ GARANTI
CorkSport - 2014-2018 Mazda 3 80mm Non-Resonated Exhaust
Performance Sound:
During testing we found that using the original 80mm exhaust made for NA Mazda 3’s produced more drone inside the cabin than what would be comfortable for most people. This led to the testing of multiple different combos of midpipes and axle backs with various resonator configurations. After testing was completed we chose to stick with the same midpipe setup, but updated the axle back to not have any resonators. This new combo builds upon the already fantastic sound that the original 80mm exhaust featured by adding an even more aggressive tone in the higher RPM range while maintaining lower drone levels than the original setup. Make sure to watch the video to get a glimpse of what you can expect out of the updated 80mm CBE for Mazda 3’s with the Turbo Kit.
Appearance Boost:
The Turbo Kit specific 80mm CBE retains the aggressive looks from the original setup featuring the same 100mm or ~4” exhaust tips. The exhaust tips found on the hatchback are slant cut with a dual wall construction to fill up the bumper cutouts and match the bumper profile. The sedan on the other hand features single wall tips so that no debris or water can get caught in the backside of the tips since they are angled downwards because there are no exhaust cutouts present in the bumper. Whichever setup you end up sporting will add a much-needed and appreciated look that will boost the aggressiveness of the rear of your car.
High Quality Materials & Manufacturing:
Each exhaust starts out with T-304 stainless steel piping that is then TIG welded and finally polished to a mirror like finish. This ensures that corrosion will not be an issue and the exhaust will last for many years to come. Each of the flanges on the exhaust are laser cut out of 9mm or ~3/8” thick material to help prevent any warping from occurring. Also included is all the necessary hardware including gaskets and step-by-step install instructions to make installation straightforward.
Noter:
- Livraison GRATUITE / FREE Delivery
2014-2018 Mazda 3 2.5L & 2.0L Hatchback
- Optimized for the CorkSport Turbo Kit, use on a naturally aspirated setup will be very loud and aggressive.