Économisez 5 % Supplémentaire sur vos achats de Roues & de Pneus de plus de 500$!
Mon garage
Ajouter un véhicule
Mon garage
- Recevez des recommandations
- Trouvez facilement vos pièces
-
COBB
-
- Noix de roues & Barrures
- Spacer de roues
- Garde-boue
-
Jantes
- Bull Bar
- Couvre-boite
- Déflecteurs de vitre
- Fender Flares & Trim
- Grilles
- Klaxon
- Marchepieds
- Miroir
- Off-Road Bumpers
- Protège aile
- Treuils Électriques
- Déflecteurs de capot
- Déflecteurs de toit
- Protecteurs de pare-choc
- Light Covers & Lamp Guards
- Entretien Automobile
- Garniture extérieur
- Grille Guards
- Rack & Rangement de toit
- Renforts et protection
- Toits souples et rigides
- Support & contour de plaque
- Emblèmes et logos
- Antenne
- Support de roue de secours
- Tow Hook
-
-
Freins
-
- Coil Springs
- Coilovers
- Amortisseurs
- Amortisseurs & Ressorts Kits
- Handling Kits
- Lift Kits
- Leveling Kits
- Sway bars & Link kit
- Steering Arms, Rods & Links
- Strut Bars
- Bushing & Support
- Ball Joints
- Composantes alignement
- Control Arm
- Contrôleur
- Steering Dampers
- Suspension à air
- Suspension à lames
- Accessoires
-
- Ensemble embrayage
- Disques de Clutch
- Pressure Plates
- Flywheels
- Transmission Refroidissement
- Supports
- Pommeau & Levier de Vitesse
- Liquide a transmission
- Cardan
- Composantes Électroniques
- Composantes Embrayage
- Différentiels
- Drive Shaft
- Driveshaft Yokes
- Flexplates
- Pan à huile
- Torque Converters
- Bearings & Moyeu de roue
- Transmission
- Transmission Shafts & Gears
- -20%
- LIVRAISON GRATUITE
H&R | ID Race Springs
ZF060-050
H&R Springs ID Race Springs
LIVRAISON GRATUITE
CAD $121,30
CAD $151,63
Économisez 20%
- FIÈREMENT CANADIEN
- GARANTIE DU MEILLEUR PRIX
- COMPATIBILITÉ GARANTI
H&R - Coil Spring
Description
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R Springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
Caractéristiques
- Free Length: 60 MM
- Rate: 50 MM
Attributs
- Wide variety of spring lengths and spring rates
- Tender springs available
- Allows custom tuning of your suspension
- Crafted from special lightweight (hf) 54SiCr6 spring steel, lighter weight, more spring travel
- 100% made in Germany
- 285 - For Off Road Use Only
Noter:
- Livraison GRATUITE / FREE Delivery
Not Application Specific