-
Shop by Category
-
- Tapis Protecteur
- Pommeau de levier de vitesse
-
- Ensembles
- Indicateurs de vitesse
- Tachometers & Shift Lights
- Température
- Voltmètre
- Niveau de carburant
- Manomètres - Pressure Gauges
- Air Fuel Ratio (AFR)
- Boost & Vacuum Pressure
- Pyrometer
- Tableau de bord de course
- Gauge Mounts & Trim sur mesure
- Capteurs et adaptateurs
- Câblage et éclairage
- Moniteurs et enregistreurs de données
- Minuteurs, horodateurs et horloges
- Garniture intérieur
- Pédales
- Rangement intérieur
- Accessoires
- Sièges auto
- Volants
- Entretien Automobile
- Tapis de coffre
- Couvre-siège
- Pare-soleil
- Antivol
-
- Spacer de roues
- Garde-boue
- Bull Bar
- Déflecteurs de vitre
- Déflecteurs de capot
- Déflecteurs de toit
- Fender Flares & Trim
- Grilles
- Klaxon
- Miroir
- Protège aile
- Protecteurs de pare-choc & seuils
- Light Covers & Lamp Guards
- Entretien Automobile
- Garniture extérieur
- Grille Guards
- Renforts et protection
- Toits souples et rigides
- Support & contour de plaque
- Emblèmes et logos
- Antenne
- Support de roue de secours
- Tow Hook
-
- Housses
- Accessoires Off-Road
-
- Engine DressUp
- Refroidisseurs huile
-
- Filtres à huile
- Oil Catch Can
-
- Huiles Moteur
- Fluides de Transmission, Huiles, Additifs
- Additifs pour Huile Moteur
- Liquides de Frein
- Liquides de Direction Assistée
- Antigel & Additifs
- Additifs pour Système de Carburant
- Lubrifiants Différentiels
- Lubrifiants pour Transfer Case
- Lubrifiants pour Suspensions
- Lubrifiants pour Roulements
- Autres
- Support
- Throttle Bodies
- Stage de Performance
- Poulies & Courroies
- Collets de serrage
- Pan à huile
- Gaskets
- Bloc Moteur
- Engine Dress Up
-
-
- Coil Springs
- Coilovers
- Amortisseurs
- Amortisseurs & Ressorts Kits
- Handling Kits
- Lift Kits
- Leveling Kits
- Sway bars & Link kit
- Steering Arms, Rods & Links
- Strut Bars
- Bushing & Support
- Ball Joints
- Composantes alignement
- Control Arm
- Contrôleur
- Steering Dampers
- Suspension à air
- Suspension à lames
- Accessoires
-
- Ensemble embrayage
- Disques de Clutch
- Pressure Plates
- Flywheels
- Transmission Refroidissement
- Supports
- Pommeau & Levier de Vitesse
- Liquide a transmission
- Cardan
- Composantes Électroniques
- Composantes Embrayage
- Différentiels
- Drive Shaft
- Driveshaft Yokes
- Flexplates
- Pan à huile
- Torque Converters
- Bearings & Moyeu de roue
- Transmission
- Transmission Shafts & Gears
-
-
- Extérieur
-
- Ensembles de démarrage et accessoires
- Éviers et drains
- Filtres à eau et cartouches
- Hivernisation
- Pompes
- Raccords de plomberie
- Rafraîchisseurs et adoucisseurs d'eau
- Régulateurs de pression d'eau
- Réservoirs de rétention
- Robinets et accessoires de douche
- Toilettes et accessoires
- Trappes et remplissages d'eau
- Tuyaux de plomberie
- Douches et baignoires
- Chauffe-eau
- Génératrice
-
- MAGASINER PAR PRODUIT
- ACHETER PAR MARQUE
- ROUES & PNEUS
- Contactez-nous
-
Mon garageAjouter un véhicule
Mon garage
- Recevez des recommandations
- Trouvez facilement vos pièces
- -10%
- LIVRAISON GRATUITE
ICON Alloys | 2020-Up Jeep JT Gladiator, Rear, Adjustable Billet Lower Link Kit
22063
2020-UP JEEP GLADIATOR JT BILLET REAR ADJUSTABLE LOWER LINK KIT
- CNC machined 6061 aluminum construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM16T PTFE-lined FK Rod Ends
- Adjustable while installed on vehicle for various lift heights & driveline angles
- Replaceable Nylon Rock Slider protects link and helps prevent hang ups while wheeling
- ICON1K tested in extreme off-road conditions
- Covered by ICON's lifetime warranty
LIVRAISON GRATUITE
CAD $1 737,38
CAD $1 930,42
Économisez 10%
- FIÈREMENT CANADIEN
- GARANTIE DU MEILLEUR PRIX
- COMPATIBILITÉ GARANTI
ICONs billet aluminum rear lower link arms for the 2020-UP Jeep Gladiator are a significant upgrade over the factory units due to increases in strength, adjustability, and performance. These links are made from CNC machined 6061 aluminum in-house and anodized for corrosion resistance, providing a major improvement over the construction of the stock units. This rear lower link arm kit features PTFE-lined FK rod ends for increased suspension articulation, reduced deflection, and on-vehicle link arm length adjustability using ICONs double adjuster system. Additionally, multi durometer bushings are installed that allow for noise free operation and maximum angularity without the need for periodic greasing and/or other maintenance. The quality rod ends and bushings featured in these link arms allow the vehicles suspension to function as intended, without the bushing bind that limits the vehicle in stock form. ICONs engineering team has also gone a step further in the development of these products by incorporating features such replaceable nylon rock sliders to prevent any hang-ups on the trail. After the design phase was completed ICON engineers put these parts through the ICON1K real-world test cycle for a final stamp of approval.
Noter:
- Livraison GRATUITE / FREE Delivery
Not Application Specific