-
MAGASINER PAR CATÉGORIE
-
-
Antivol
-
Tapis Protecteur
-
- Ensembles
- Indicateurs de vitesse
- Tachometers & Shift Lights
- Température
- Voltmètre
- Niveau de carburant
- Manomètres - Pressure Gauges
- Air Fuel Ratio (AFR)
- Boost & Vacuum Pressure
- Pyrometer
- Tableau de bord de course
- Gauge Mounts & Trim sur mesure
- Capteurs et adaptateurs
- Câblage et éclairage
- Moniteurs et enregistreurs de données
- Minuteurs, horodateurs et horloges
-
Pommeau de levier de vitesse
-
Garniture intérieur
-
Rangement intérieur
-
Accessoires
-
Volants
-
Esthétique Intérieur
-
Couvre-siège
-
Sièges auto
-
Pare-soleil
-
-
-
-
-
-
Coil Springs
-
Coilovers
-
Amortisseurs
-
Amortisseurs & Ressorts Kits
-
Handling Kits
-
Lift Kits
-
Leveling Kits
-
Sway bars & Link kit
-
Steering Arms, Rods & Links
-
Strut Bars
-
Bushing & Support
-
Ball Joints
-
Composantes alignement
-
Control Arm
-
Contrôleur
-
Steering Dampers
-
Suspension à air
-
Suspension à lames
-
Accessoires
-
-
-
Ensemble embrayage
-
Disques de Clutch
-
Pressure Plates
-
Flywheels
-
Transmission Refroidissement
-
Supports
-
Pommeau & Levier de Vitesse
-
Liquide a transmission
-
Cardan
-
Composantes Électroniques
-
Composantes Embrayage
-
Différentiels
-
Drive Shaft
-
Driveshaft Yokes
-
Flexplates
-
Pan à huile
-
Torque Converters
-
Transmission Shafts & Gears
-
- MAGASINER PAR PRODUIT
- ACHETER PAR MARQUE
- ROUES & PNEUS
- Contactez-nous
-
Mon garageAjouter un véhicule
Mon garage
- Recevez des recommandations
- Trouvez facilement vos pièces
- -15%
- Nouveau
- LIVRAISON GRATUITE
Mishimoto | Intercooler Pipe Kit, Black, Hot-side, fits Ford Focus ST 2013-2018 - Focus 2.0T 2013-2018
- FIÈREMENT CANADIEN
- GARANTIE DU MEILLEUR PRIX
- COMPATIBILITÉ GARANTI
Mishimoto - Intercooler Pipe Set
Description
Open up the flow of the charged air in your 2013-2018 Ford Focus ST with the Mishimoto hot-side intercooler pipe. The stock hot-side pipe in your Focus ST is plagued with bends, a restrictive inner diameter and muffling equipment which slows the airflow and causes turbulence on the way to the intercooler. Mishimoto's hot-side intercooler kit not only reduces the amount of bends, but also increased the diameter to 2.5? giving it a 14-percent increase in volume over the stock piping meaning better flow and the added bonus of 8hp and 10ft/lbs of torque.While a majority of the stock piping is constructed from aluminum already, the couplers are made from degradation-prone rubber. Our kit includes more durable silicone couplers featuring 5-layers of heat-resistant fibers and wire reinforcement to ensure that the Mishimoto hot-side intercooler pipe can stand up to the heat. This kit is offered in a polished finish as well as a wrinkle black powder coat, and is covered under Mishimoto's Lifetime Warranty.
Caractéristiques
- 10900: Worm Gear
- 11252: 2 IN
- 11253: 2 IN
- 1882: Yes
- 200: Powder Coated
- 3530: Aluminum
- 3531: Black
- 3606: 4
- 5745: Black
- 5746: Silicone
- 7703: 1
- 9790: Mandrel
- Install Difficulty: 3
- OptionLabel: Wrinkle Black
- TechSpec Applications: Ford Focus ST, 2013-2018
- TechSpec Includes: (1) Aluminum Intercooler Pipe--(2) Silicone Couplers--(4) High-Torque Worm Gear Clamps--Mishimoto Lifetime Warranty
- TechSpec Inlet (in): 2
- TechSpec Installation Notes: 27 in-lbs (3NM) recommended for all T-bolt and constant-tension T-bolt clamps. These clamps have an operating range of 18-35 in-lbs (2-4NM). Do not exceed the maximum torque rating of 35 in-lbs (4NM).
- TechSpec Outlet (in): 2.5
Attributs
- 14-percent increase in volume over stock hot-side pipe
- 2.5-in Mandrel-bent aluminum piping
- 26-percent greater flow than stock hot-side pipe
Noter:
- Livraison GRATUITE / FREE Delivery
Ford
2013-2018 Focus ST L4 2.0L Turbo SEE NOTE1
Note 1: EO D-759-6;